Here you'll find the essential tune-up specifications for the 1995-2000 2.0L Dodge Stratus and Plymouth Breeze.
Contents of this tutorial:
You can find this tutorial in Spanish here: Especificaciones De Afinación y Del Motor (195-2000 2.0L Dodge Stratus, Plymouth Breeze) (at: autotecnico-online.com).
APPLIES TO: Applies to the following vehicles:
- 2.0L Dodge Stratus: 1995, 1996, 1997, 1998, 1999, 2000.
- 2.0L Plymouth Breeze: 1996, 1997, 1998, 1999, 2000.
Ignition System Specifications
| Ignition Coil Resistance (@ 70 °F) | |
|---|---|
| Primary | 0.45-0.65 Ohms |
| Secondary | 7,000-15,8000 Ohms |
| Spark Plug Wire Resistance Specification | |
|---|---|
| Cylinder 1 or 4 | 3500-4500 Ohms |
| Cylinder 2 or 3 | 2950-4100 Ohms |
| Spark Plug Gap | Torque |
|---|---|
| 0.033-0.038 inches (.84-.97 MM) | 20 Ft. lbs. (27 N.m.) |
| Base Ignition Timing |
|---|
| Non ajustable. |
| OE Spark Plug |
|---|
| Champion RC9YC |
The following tutorial will help you test the ignition system:
- How To Test The Ignition Coil (1995-2000 2.0L Dodge Stratus, Plymouth Breeze)
- How To Test The Cam Sensor (1995-1999 2.0L Dodge Stratus, Plymouth Breeze)
- How To Test The CKP Sensor (1995-2000 2.0L Dodge Stratus, Plymouth Breeze)
Fuel System Specifications
The electric fuel pump is located inside the fuel tank.
| Fuel Pressure With The Key On Engine Off |
|---|
| 46-50 PSI |
| Fuel Pressure With The Key On Engine Running |
|---|
| Not Given |
The following tutorial will help you test the fuel pump:
| Fuel Injector Resistance |
|---|
| 10-16 Ohms (individual resistance at room temp). |
The following tutorial will help you test the fuel injectors:
Drive Belt Routing Diagram
Intake Manifold Bolt Torque Specifications
The illustration above shows the intake manifold bolt tightening sequence to avoid damage to the intake manifold gasket or vacuum leaks.
NOTE: Install the intake manifold gaskets without any type of sealer.
| Intake Manifold Bolt Torque Specifications |
|---|
| 106 Inch Lbs. |
Exhaust Manifold Bolt Torque Specifications
NOTE: Install the exhaust manifold gaskets without any type of sealer.
| Exhaust Manifold Bolt Torque Specifications |
|---|
| 17 Ft. Lbs. |
Cylinder Head Bolt Torque Specifications
The illustration above shows the cylinder head bolt tightening sequence.
Before installing the cylinder head bolts, clean and oil their threads. Short head bolts should be installed in positions 7, 8, 9, and 10.
NOTE: Install the cylinder head gasket without any type of sealer.
| Cylinder Head Torque Specifications | |
|---|---|
| Step 1 | 25 Ft. Lbs. (34 N.m) |
| Step 2 | 50 Ft. Lbs. (68 N.m) |
| Step 3 | 50 Ft. Lbs. (68 N.m) |
| Step 3 | Tighten an additional 1/4 turn (DO NOT use a torque wrench!) |
If this info saved the day, buy me a beer!
