How To Test: P0107 OBD II Trouble Code (Honda 2.2L, 2.3L)

TEST 4: Bench Testing The MAP Sensor

How To Test A P0107 Diagnostic Trouble Code (Honda 2.2L, 2.3L)

Now that you've confirmed that the MAP sensor is getting both power and Ground, the last thing we need to do is bench test it.

Bench testing the MAP sensor will let us know beyond a shadow of a doubt if the MAP sensor is bad or not.

In a nutshell, we're gonna' remove the MAP sensor from the intake manifold, connect the multimeter to it, then manually apply vacuum to the MAP sensor (while it's still connected to its connector) and see if the MAP sensor's output voltage changes.

If you don't have a multimeter or need to upgrade yours, check out my recommendation here: Abe's Multimeter Recommendation (at: easyautodiagnostics.com).

I'll show you how. This is what you'll need to do:

  1. 1

    Remove the MAP sensor from the top of the intake manifold.

    Reconnect the MAP sensor to its electrical connector, if you had to unplug it to remove it, since this test requires that the MAP sensor stay connected to its 3-wire electrical connector.

  2. 2

    Connect your multimeter's red test lead to the wire that connects pin number 3 of the MAP sensor (see image above).

    You'll need to back-probe the MAP sensor connector or use a wire piercing probe to connect your multimeter to this circuit (you can see what a wire piercing probe looks like here: Wire Piercing Probe).

  3. 3

    Ground the black multimeter test lead.

    I suggest grounding the black multimeter test lead directly on the battery negative (-) terminal.

  4. 4

    Turn the key on (but don't start the engine) and take a look at what voltage your multimeter is registering.

    It should register around 2.9 Volts (± 1 V). If your multimeter is registering something different at this point, don't panic because right now you're just setting up the test.

  5. 5

    Attach a vacuum pump to the MAP sensor's vacuum inlet nipple using the appropriate size vacuum hose.

    If you don't have a vacuum pump, you can use the ‘good ole' lungs’ and provide the necessary with your mouth.

  6. 6

    The voltage, your multimeter is registering, should decrease as you apply vacuum with your vacuum pump (or with your mouth).

  7. 7

    The MAP sensor's voltage, as registered on your multimeter, should increase back to the original voltage value you saw in step 4 as you release the vacuum you applied with the vacuum pump (or your mouth).

NOTE: Applying vacuum should make the MAP signal voltage get smaller. Releasing vacuum should make the MAP signal voltage get bigger (back to the original voltage you saw at the beginning of this test).

Let's take a look at what your test results mean:

CASE 1: The MAP sensor's voltage decreased and increased as you applied and released vacuum. This confirms that the MAP sensor is good and operating normally.

This test result completely eliminates the MAP sensor on your Honda as bad. If you're still having the MAP sensor trouble code come back, take a look at: MAP Sensor Is Good But Code Doesn't Go Away!.

CASE 2: The MAP sensor's voltage DID NOT decrease or increase as you applied and released vacuum. This confirms that the MAP sensor is bad and needs to be replaced.

If you need to buy the MAP sensor and would like to save some bucks, take a look at the section: Where To Buy The MAP Sensor.

MAP Sensor Is Good But Code Doesn't Go Away!

Several things can cause the PCM to think that the MAP sensor is bad when it really isn't. In this section I'll offer a few tips and/or suggestions:

  1. Check engine mechanical health.
    • This means doing a compression test.
    • What you're looking for is uneven wear and tear between the cylinders. This means that the compression each cylinder is producing varies more than 15%.
    • This tutorial will help: How To Test Engine Compression (Honda 2.2L, 2.3L).
  2. Make sure that the MAP sensor is getting power and Ground.
  3. A short in the wiring between the MAP sensor and the PCM.
    • You'll need to check the continuity of the 3 wires between the MAP sensor and the PCM using the appropriate wiring diagram.
  4. A bad PCM.
  5. A fuel system malfunction (that is also setting other trouble codes.
    • If there are any other trouble codes, you'll need to diagnose and repair these first (since they may be indirectly causing the P0107 code).
  6. You've replaced the throttle body gasket and used silicone sealer on it and this sealer has plugged the MAP sensor's vacuum passage and/or orifice (I've seen this happen a lot!).

More Test Articles

If this article has helped, or in the least it has been informative, check the other in the Honda 2.2L, 2.3L index. You can find this index here: Honda 2.2L, 2.3L Index Of Articles.

Here's a small sample of the articles/tutorials you'll find in the index:

Thank You For Your Donation

If this info saved the day, buy me a beer!

If This Info Saved the Day, Buy Me a Beer!

Honda Vehicles:

  • Accord 2.2L, 2.3L
    • 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002
  • Odyssey (EX LX) 2.2L
    • 1995, 1996, 1997, 1998
  • Prelude 2.2L
    • 1995, 1996

Acura Vehicles:

  • CL 2.2L
    • 1997, 1998, 1999

Isuzu Vehicles:

  • Oasis 2.2L
    • 1996, 1997, 1998, 1999